vfs_aio_pthread — pthread poolを使うSamba vfs中の非同期I/Oの実装
vfs objects = aio_pthread
この VFS モジュールは samba(7)システムの一部である。
aio_pthread
VFS モジュールは、pthread APIが
有効で、Posix AIOインタフェースを使っていないプラットフォーム上で、
Samba用の非同期I/Oを有効にする。Posix AIOはきつい制限によって使いづらい。
たとえば、あるバージョンのLinuxでは、使用するリアルタイムシグナルは
高負荷の時には動作が不正になる。その他のシステムでは、特別なカーネル
モジュールがロードされるときにのみAIOが有効になるか、特定の、システム全体での
非同期要求がスケジュールされている時にのみAIOが許可される。
(ほとんどのLinuxシステムで使われている)glibcベースのシステムでは、
glibcの実装を使うシステム上でPOSIX AIOを本質的に使えなくさせる、
ファイルディスクリプタ毎の、単一の未処理要求のみを許可する。
aio_pthread
VFSmodule enables asynchronous
I/O for Samba on platforms which have the pthreads API available,
without using the Posix AIO interface. Posix AIO can suffer from severe
limitations. For example, on some Linux versions the
real-time signals that it uses are broken under heavy load.
Other systems only allow AIO when special kernel modules are
loaded or only allow a certain system-wide amount of async
requests being scheduled. Systems based on glibc (most Linux
systems) only allow a single outstanding request per file
descriptor which essentially makes Posix AIO useless on systems
using the glibc implementation.
これらのすべての実装を直すため、aio_pthreadモジュールが 作成された。これは、読み取りと書き込みの呼び出しを非同期に処理する ことができるようにするため、内部Posix AIOインタフェースの代わりに、 ptherad poolを使用する。workとして新しいスレッドを作成することに よる、動的に拡張されるpthead poolが作成され、それは、smbdプロセス毎に 最大100スレッドまで割り当てられる。この制限を変更するには、下記の "aio num threads"を参照のこと。新しいスレッドは、新しい読み取りか 書き込み要求が受け取られた時に有効なアイドルスレッドがあった場合には 作成されず、新しいworkは存在するアイドルスレッドに割り当てられる。 スレッドはもしも1秒アイドルになった時にそれ自身を終了する。
To work around all these limitations, the aio_pthread module was written. It uses a pthread pool instead of the internal Posix AIO interface to allow read and write calls to be process asynchronously. A pthread pool is created which expands dynamically by creating new threads as work is given to it to a maximum of 100 threads per smbd process. To change this limit see the "aio num threads" parameter below. New threads are not created if idle threads are available when a new read or write request is received, the new work is given to an existing idle thread. Threads terminate themselves if idle for one second.
smb.confパラメーターaio write size
と
aio write size
はこのモジュールを有効にするために
適切に設定する必要があることに注意。
Note that the smb.conf parameters aio read size
and aio write size
must also be set appropriately
for this module to be active.
このモジュールは、Samba VFS pread/pwriteインタフェースが スレッドセーフではないので、任意のモジュールスタックの最後に 位置づけなければならない。このモジュールは直接preadとpwrite システムコールを使い、Samba VFS preadとpwriteインタフェースを 呼び出さない。
This module MUST be listed last in any module stack as the Samba VFS pread/pwrite interface is not thread-safe. This module makes direct pread and pwrite system calls and does NOT call the Samba VFS pread and pwrite interfaces.
簡単な使い方:
[cooldata]
path = /data/ice
aio read size = 1024
aio write size = 1024
vfs objects = aio_pthread
IO要求を提供するためのthread pool中に作成される、 smbd毎のスレッドの最大数を制限する。
既定値ではこの値は 100である。